317 Rte 27, Raymond, NH 03077

Dur-A-Lift Custom Bucket Trucks & DINOlift Aerial Lifts

No items found.

AC Communications Splicer

Build Overview

Lift Specs

  • DTAS2-35TS 35’ telescopic articulated aerial, non-insulated
  • Pedestal Riser
  • 36’ of platform height
  • 41’ of working height
  • 27’6” side reach
  • Platform capacity of 350 lbs.
  • Bucket configured as follows:
  • 24” x 30” x 42”
  • End hung bucket
  • Walk thru bucket with door
  • Electric toggle switch
  • Emergency Power
  • Engine Start/Stop
  • 370 degree Non-Continuous rotation.
  • Open center hydraulic system
  • Non-relube bearings used throughout.
  • Integral hydraulic oil reservoir with dual sight gauges
  • Emergency Power Insulated 12V DC hydraulic system.
  • Master / Slave hydraulic leveling with upper and lower control to tilt for cleanout or rescue.
  • Lower remote controls mounted in rear compartment
  • Upper boom storage cradle with ratchet type tie down strap and tubular rubber platform support.
  • Body harness and lanyard.
  • Standard white urethane paint.
  • Two operator’s manuals and two service manuals.
  • ANSI A92.2 Data plate.
  • Internal hydraulic tank
  • Generator driven hydraulic pump
  • Open circuit operation
  • Emergency Brake Interlock

Body Specs

  • Brand FX Fiberglass Service Body, BFXB-84
  • 132” long x 42” high x 94” wide.
  • 84” CA with dual rear wheels.
  • 42” compartment height
  • 20” compartment depth
  • 25” body mounting height

Splicing/Interior

  • One (1) Birch countertop installed on the top of the curbside side compartment
  • structure. Counters shall extend from the rear of the body and be approximately
  • 96” long x 24” wide x by 2” thick. Directly below this counter area shall be storage
  • created by aluminum risers supporting the counter. HEIGHT TBD per customer
  • One (1) curbside corner hinged splicing door
  • Fasclamp Fiber hold down fixture
  • Streetside compartment tops left open
  • Four (4) ECCO #EW0701, 21.5” LED ceiling light, 12 vdc, switched and mounted on the ceiling above the counter. Controlled by a switch at the rear doors
  • One (1) Ventline 14” x 14” Roof Vent, with crank open dome and 12 vdc powered integral fan. Controlled by a switch at the rear doors
  • Carbon Monoxide Monitor and Alarm
  • One (1) 24” x 15” curbside sliding body window with screen, Motion Window model #1100

120 VAC:

  • Install a Predator 9500 watt Gas Inverter/Generator on the streetside of the tailshelf.
  • 9.5 kW output
  • 58.3 amp
  • 120 VAC
  • 60 Hz, single phase
  • GE TPL Weather Resistant Breaker Panel in the streetside rear compartment
  • One (1) Plugmold outlet strips shall be provided one at the counter area. Each strip shall be approximately 48” long and be equipped ten (10) outlets wired to operate from the generator
  • 120 VAC, 15 amp

Heading

TEST

Product Overview

Headings, paragraphs, blockquotes, figures, images, and figure captions can all be styled after a class is added to the rich text element using the "When inside of" nested selector system.

Rich Text Element

What’s a Rich Text element?

The rich text element allows you to create and format headings, paragraphs, blockquotes, images, and video all in one place instead of having to add and format them individually. Just double-click and easily create content.

The rich text element allows you to create and format headings, paragraphs, blockquotes, images, and video all in one place instead of having to add and format them individually. Just double-click and easily create content.

Static and dynamic content editing

Static and dynamic content editing

A rich text element can be used with static or dynamic content. For static content, just drop it into any page and begin editing. For dynamic content, add a rich text field to any collection and then connect a rich text element to that field in the settings panel. Voila!

A rich text element can be used with static or dynamic content. For static content, just drop it into any page and begin editing. For dynamic content, add a rich text field to any collection and then connect a rich text element to that field in the settings panel. Voila!

How to customize formatting for each rich text

How to customize formatting for each rich text

Headings, paragraphs, blockquotes, figures, images, and figure captions can all be styled after a class is added to the rich text element using the "When inside of" nested selector system.

Headings, paragraphs, blockquotes, figures, images, and figure captions can all be styled after a class is added to the rich text element using the "When inside of" nested selector system.

No items found.

AC Communications Splicer

Build Overview

Lift Specs

  • DTAS2-35TS 35’ telescopic articulated aerial, non-insulated
  • Pedestal Riser
  • 36’ of platform height
  • 41’ of working height
  • 27’6” side reach
  • Platform capacity of 350 lbs.
  • Bucket configured as follows:
  • 24” x 30” x 42”
  • End hung bucket
  • Walk thru bucket with door
  • Electric toggle switch
  • Emergency Power
  • Engine Start/Stop
  • 370 degree Non-Continuous rotation.
  • Open center hydraulic system
  • Non-relube bearings used throughout.
  • Integral hydraulic oil reservoir with dual sight gauges
  • Emergency Power Insulated 12V DC hydraulic system.
  • Master / Slave hydraulic leveling with upper and lower control to tilt for cleanout or rescue.
  • Lower remote controls mounted in rear compartment
  • Upper boom storage cradle with ratchet type tie down strap and tubular rubber platform support.
  • Body harness and lanyard.
  • Standard white urethane paint.
  • Two operator’s manuals and two service manuals.
  • ANSI A92.2 Data plate.
  • Internal hydraulic tank
  • Generator driven hydraulic pump
  • Open circuit operation
  • Emergency Brake Interlock

Body Specs

  • Brand FX Fiberglass Service Body, BFXB-84
  • 132” long x 42” high x 94” wide.
  • 84” CA with dual rear wheels.
  • 42” compartment height
  • 20” compartment depth
  • 25” body mounting height

Splicing/Interior

  • One (1) Birch countertop installed on the top of the curbside side compartment
  • structure. Counters shall extend from the rear of the body and be approximately
  • 96” long x 24” wide x by 2” thick. Directly below this counter area shall be storage
  • created by aluminum risers supporting the counter. HEIGHT TBD per customer
  • One (1) curbside corner hinged splicing door
  • Fasclamp Fiber hold down fixture
  • Streetside compartment tops left open
  • Four (4) ECCO #EW0701, 21.5” LED ceiling light, 12 vdc, switched and mounted on the ceiling above the counter. Controlled by a switch at the rear doors
  • One (1) Ventline 14” x 14” Roof Vent, with crank open dome and 12 vdc powered integral fan. Controlled by a switch at the rear doors
  • Carbon Monoxide Monitor and Alarm
  • One (1) 24” x 15” curbside sliding body window with screen, Motion Window model #1100

120 VAC:

  • Install a Predator 9500 watt Gas Inverter/Generator on the streetside of the tailshelf.
  • 9.5 kW output
  • 58.3 amp
  • 120 VAC
  • 60 Hz, single phase
  • GE TPL Weather Resistant Breaker Panel in the streetside rear compartment
  • One (1) Plugmold outlet strips shall be provided one at the counter area. Each strip shall be approximately 48” long and be equipped ten (10) outlets wired to operate from the generator
  • 120 VAC, 15 amp

Interested in a custom bucket truck or DINO for your business?
Get started today.