‍Lift Specs

• DPM-2-47DU Insulated 47/49’ telescopic / articulating aerial platform lift.
• Up to 54’ of working height
• Platform capacity:
• 550 lbs. without jib in operation
• 400 lbs. with jib in use
• Jib:
• Top/Rear mounted
• 1000# maximum capacity
• Removable
• 80’ of .5” load line with hook and clevis
• Hydraulic and pinnable extension
• Self locking hydraulic operated worm gear winch
• Bucket mounted hydraulic controls which include:
• 4 Axis HERC High Electrical Resistance “Single Stick: Control
• Emergency Power
• Engine Start/Stop
• 180 degree bucket rotation
• Bucket Elevator
• Jib Controls
• Bucket:
• 24” x 30” x 42” fiberglass bucket
• Vinyl cover with lanyard
• 22” hydraulic operated bucket elevator
• Bucket Liner with step
• Insulation:
• Inner Telescopic Boom
• Upper Boom Wrap
• Lower Boom Isolator
• Compensation Link Isolator
• Stabilization:
• Front “A” Frame Outriggers
• Rear “A” Frame, short stance
• Safety:
• Parking Brake Interlock
• Outrigger “Down” Interlock
• Remote lower controls with override.
• Continuous rotation.
• Seven GPM open center hydraulic system
• Non-relube bearings used throughout.
• Integral hydraulic oil reservoir with dual sight gauges and 17 gallon capacity.
• Emergency Power Insulated 12V DC hydraulic system.
• Master / Slave hydraulic leveling with upper and lower control
• Upper boom storage cradle with latching tie down strap and tubular rubber platform
• support.
• Full Body Harness and Lanyard.
• Standard white urethane paint.
• Two operator’s manuals and two service manuals.
• ANSI A92.2 Data plate.
• 10 Gallon internal hydraulic tank
• PTO operated hydraulic pump

Body Specs

• BrandFX 124” Fiberglass Utility Body
• Steel Understructure
• Aluminum Treadplate Floor
• 94” Width
• 54” Floor Width
• 42” Compartment Height
• 18” Compartment Depth
• 25” Floor Height
• Standard Shelving
• Standard Bright White Gelcoat
• Street Side Compartments:
• 1V: 30.5” W x 42” H
• 2V: 22.625” W x 42” H
• H: 40” L x 18.5” H
• 3V: 31” L x 42” h
• Curbside Compartments:
• 1V: 30.5” W x 42” H
• 2V: 22.625” W x 42” H
• H: 40” L x 18.5” H
• 3V: 31” L x 42” h
• Tailshelf
• Aluminum Treadplate surfaced, structurally supported, 30” deep tailshelf
• LED ICC lighting to include stop/turn/tail and back lights
• Curbside stepway access with aluminum grab loop access handle
• Flexible stepway access step
• Chrome grab handle on rear compartment bulkhead
• Rear ICC bumper with 2” receiver mounting for a future hitch, chain loops and
• RV Trailer Socket with cover
• Electrical:
• Warning Lights:
• Two (2) 4” round Amber LED flashers, installed in tailshelf
• Two (2) ECCO surface mount LED front grille flashers
• Two (2) Federal LED Beacons with Branch Guards mounted on headboard
• Other/Misc Lighting/Electrical:
• Two (2) ECCO LED remote control spotlight mounted on the headboard
• One (1) 4” LED Stepway light
• Two (2) 4” LED Work light mounted on the headboard
• One (1) Back-up Alarm
• Move existing inverter to new chassis with new batteries in the loadbed
• Additional equipment
• Two (2) Inclinometers, installed one (1) at each outrigger control
• Two (2) outrigger pad holders
• Four (4) Dica Composite Outrigger Pads
• Fire extinguisher, 5lb
• Reflector kit
• First aid Kit
• Two (2) composite wheel chocks
• M-Series tool box 132” W x 18” H x 16” D mounted on top of driver side
• compartments. Box will be made of .125 smooth aluminum. Single latching doors